This article below relating to A Step-by-Step Guide to Installing a Bathtub is truly intriguing. Have a go and make your own assumptions.
Mounting a bath tub isn't exactly rocket science, yet it does require strong plumbing, carpentry, and often, tiling skills. Changing an old tub with a brand-new one is likewise a moderately tough project. If the old bathtub is readily accessible, the job can move immediately; if you have to open up a wall surface to remove the old bathtub and also position the new bath tub, the job is much harder. In either situation, the job is within a house handyman's skills, although you will require an assistant to leave the old tub and also embeded in the new one. Make sure you have actually certified yourself for the work as well as are comfortable trying it. Instead of hiring a contractor to take control of a halfway-completed job, it is far better to think about employing one prior to you begin. Opportunities are you may require a specialist plumber to make tube links.
This write-up will aid you mount a brand-new bath tub in your bathroom if you have actually already purchased a new bathtub and don't need to change the plan of your previous supply of water pipes.
Your tools and product list need to make up the following:
Planning for the Installation
Firstly, the sustaining frame supplied with the bath needs to be fitted (if required) according to the producer's directions. Next off, fit the taps or mixer to the tub. When suitable the faucet block, it is essential to make certain that if the faucet comes with a plastic washer, it is fitted between the bath and also the faucets. On a plastic bath, it is also sensible to fit a supporting plate under the taps unit to avoid stress on the tub.
Fit the versatile faucet connectors to the bottom of both taps using 2 nuts and olives (occasionally provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet with the hole in the bath. Make use of the nut supplied by the maker to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the flexible overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bathroom. See to it you use all of the supplied washers.
Connect the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom must now be ready to be suited its last setting.
Removing Old Taps
If you require to change old faucets with brand-new ones as a part of your installation, after that the first thing you need to do is disconnect the supply of water. After doing so, activate the faucets to drain any water staying in the system. The process of eliminating the existing faucets can be fairly bothersome due to the restricted access that is typically the situation.
Use a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipes to the faucets. Have a towel ready for the remaining water that will come from the pipes. As soon as the supply pipes have been removed, make use of the same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary taps from transforming during this process. When the faucets have been eliminated, the holes in the bath/basin will certainly need to be cleaned of any type of old sealing substance.
Prior to moving on to fit the new taps, compare the pipe connections on the old taps to the new taps. If the old taps are longer than the new faucets, then a shank adapter is required for the brand-new faucets to fit.
Setting up the Bathtub
Using both wood boards under its feet, put the bathtub in the called for setting. The wooden boards are handy in uniformly spreading the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto 4 little points.
The following goal is to guarantee that the bathtub is leveled all round. This can be accomplished by inspecting the spirit level as well as readjusting the feet on the tub up until the level checks out level.
To set up taps, fit all-time low of the outermost versatile faucet connector to the ideal supply pipe by making a compression sign up with; after that do the same for the various other faucet.
Switch on the water and inspect all joints and also brand-new pipework for leaks as well as tighten them if essential. Load the bathtub and likewise inspect the overflow electrical outlet and also the regular electrical outlet for leakages.
Finally, fix the bath paneling as explained in the maker's user's manual. Tiling and sealing around the bath tub ought to wait till the tub has actually been utilized at the very least once as this will certainly settle it right into its last position.
Suitable New Taps
If the tails of the new faucets are plastic, then you will need a plastic port to stop damage to the string. One end of the port fits on the plastic tail of the tap as well as the other end gives a link to the existing supply pipes.
If you require to fit a monobloc, then you will call for minimizing couplers, which attaches the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next, place the tap in the mounting opening in the bath/basin making certain that the washing machines remain in area between the faucet and the sink. Protect the faucet in place with the maker given backnut. Once the faucet is firmly in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with typical tap ports. The former kind must be attached to the faucet finishes initially, tightening up only by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Bath tub
In the area where the bathroom satisfies the tile, it is essential to seal the accompanies a silicone rubber caulking. This is necessary as the fitting can move enough to crack a stiff seal, triggering the water to penetrate the wall between the bathroom and the tiling, resulting in complications with dampness and possible leaks to the ceiling listed below.
You can select from a range of coloured sealants to assimilate your fixtures as well as fittings. They are marketed in tubes and also cartridges, and can sealing voids as much as a width of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of drenched newspaper or soft rope. Keep in mind to constantly fill up the bath tub with water prior to securing, to allow for the movement experienced when the tub is in use. The sealant can split relatively very early if you do not take into account this movement before sealing.
Alternatively, ceramic coving or quadrant tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are additionally quickly available on the marketplace. It is a good idea to fit the tiles making use of water-resistant or waterproof sticky and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you like reading up on How to Install a Bathtub Yourself? Place a comment down below. We would be pleased to see your thoughts about this article. We are looking forward that you come back again before long. Sharing is caring. You won't know, you could be doing someone a favor. We truly appreciate reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Act, don't delay!